Assembler Installer General B
Mechanics in this position assemble precision and structural aircraft components and sub-assemblies. These sub-assemblies are later incorporated in larger assemblies that are subsequently installed on the airplane. Employment in this position also requires lifting and pushing/pulling up to 35 pounds, rotation of head/neck, bending and twisting at the waist, walking, standing, kneeling, reaching, sitting, climbing/balancing, use of high and low impact vibratory tools, flexion/extension, contact with metals, lubricants, solvents and plastics, exposure to noise, and the use of personal safety gear for face, eyes, hand/arm and ears. Additional Tasks, Duties and Responsibilities: Locate work area using drawings which specifies airplane number, section number, and three-point location. Obtain and verify kitted (pre-picked) detail parts, standards, and assemblies were issued correctly. Ensure that parts issued are effective for the airplane and are free of visible defects. If parts are not pre-picked, get parts and ensure that parts selected are effective for the airplane and are free of visible defects. Set up assembly tools per tooling instructions or drawing. Review bar chart or automated time line to determine which job to work on and obtain appropriate drawings for job. Operate mechanical lifts of various types (e.g. tiger and snorkel lifts), as required, to locate parts/assemblies into position or to perform assembly work. Locate tools and/or parts on airplane using tooling holes, pilot holes, K holes, or by hand (as required), per drawing or tooling instructions. Align parts and secure in place using Clecos or tooling/hand clamps. Check for good edge margins and alignment. Shim and/or trim parts as required. Select drill bits, reamers and/or countersinking tools for pilot and full size holes. Locate, drill pilot holes using drill motor and proper size drill bit(s). Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor. Set countersinking tools to proper depth as required. Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners. Use solvents to clean surfaces prior to sealing or assembly. Apply sealant, alodine, primer, adhesives and special finishes. Load and unload ovens to bond detail parts to assemblies. Apply permanent or temporary part mark and protective material to assemblies for preparation of shipment. Handle and dispose of hazardous materials in approved manner. Determine and obtain correct type and size fasteners. Cold work holes to prepare for close tolerance fastener installation. Install bushings into housings using arbor press and/or hydraulic puller. Apply liquid nitrogen to facilitate installation of bushings. Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner). Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing.
Competencies
Drill, ream, hone, bore, lap and/or countersink straight and close tolerance holes.
Competencies
Make basic layouts on parts or assemblies in order to establish reference points and to check dimensions.
Competencies
Operate computing equipment to access job information (e.g., drawings, specifications and other online information systems).
Competencies
Read and interpret engineering drawings. Capable of visualizing a three-dimensional shape from a two-dimensional view, converting left-hand to right-hand views and understanding symbols, flag notes, and general notes.
Competencies
Use math that includes addition, subtraction, multiplication, division, decimals and fractions.
Competencies
Use various types of floor-mounted power tools (e.g. bandsaw, grinder, drill press, disk sander).
Competencies
Use various types of hand tools and/or hand-held power tools.
Competencies
Use various types of precision measuring tools.
Competencies
Work with others as part of a team which includes giving and receiving feedback, assisting others in completion of tasks; possess interpersonal, listening, and participation skills.
Basic Qualifications For ConsiderationDo you have experience reading and interpreting assembly instructions or drawings?
Do you have experience using a computer such as internet navigation, email, and/or other specialized computer applications?
Do you have formal training/certification or or a minimum of 2 years experience in component assembly, systems installation and/or maintenance, repair and overhaul or an A&P license?
Typical Education/Experience
High school graduate or GED preferred.
Other Job related information
This is an hourly position governed by the IAM Collective Bargaining agreement. Resumes of current Puget Sound Boeing employees submitted via BESS will not be considered. Current Boeing employees working in Puget Sound, Wichita and Portland must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool.
- Business Unit Commercial Airplanes
- Division Bca Airplane Programs
- Program Bca Airplane Programs
- Job Type Hourly
- Experience Level Entry
- US Person Status Required? Yes
Closing Date: 02/26/2012
